Effective Date: 01/05/2007

 Product Bulletin

green divider line

 Material Safety Data Sheet
 Manufacturer's Name: Alken-Murray Corporation
 Manufacturer's Address: P.O. Box 400, New Hyde Park, New York 11040
  T: 540-636-1236 Fax: 718-224-0754
 Manufacturer's Cage Code: 2A384

green divider line

NFPA Hazard Ratings:

 0=Minimal, 1=Slight, 2=Moderate, 3=Serious, 4=Severe

 Health=1  Fire=1  Reactivity=0


green divider line

All ingredients on Canadian DSL and USA TSCA lists

green divider line

 1. Product Identification

 Synonyms:  Solutions A3050L
 CAS Number:  Not applicable to mixtures
 Chemical Formula:  mixture
 Formula ID Codes:  33050

green divider line

2. Composition/Information on Ingredients

Ingredients not precisely identified are proprietary and/or non-hazardous. All chemical ingredients appear on the EPA TSCA inventory.
 Chemical Name  CAS Number  OSHA PEL  ACGIH TLV   % Weight
2-propanoic acid, sodium salt, polymer with 2-propenamide  25085-02-3   NDA   NDA   67 - 79
Light, Low Odor Petroleum hydrotreated solvent  64742-47-8  NDA   NDA   20 - 30
Nonylphenoxypoly- (ethyleneoxy) ethanol, NP-9, nonionic surfactant  26027-38-3  NDA   NDA   1 - 3

green divider line

 3. Hazards Identification

Emergency Overview: Caution: Irritant to eyes, skin. Heated vapors irritate respiratory tract.

Potential Health Effects:

  • Signs and Symptoms of Acute Overexposure: Eye, skin irritation. Inhalation of heated vapors may irritate the respiratory tract.
  • Signs and Symptoms of Chronic overexposure: Prolonged inhalation of concentrated.heated vapors may cause damage to the kidneys. Reddening and swelling of affected area with possile itching, burning or other discomfort.
  • Medical Conditions Generally Aggravated by Exposure: Existing cuts, rashes, allergies, or other sensitive areas.
  • Ingestion: Ingestion may result in abdominal pain, nausea, and vomiting.

green divider line

 4. First Aid Measures

  • Inhalation: Remove victim to fresh air
  • Ingestion: Give victim water or milk to drink to dilute the product. Get medical advice..
  • Skin Contact: Remove contaminated clothing and footwear. Wash skin with soap and water. Wash clothing before reuse.
  • Eye Contact: Immediately flush eyes with water for 15 minutes. Get medical attention.
  • Note to Physician: None

green divider line

 5. Fire Fighting Measures

 Flash Point: > 200 degrees F (PMCC)

Flammability Limits: NDA

Autoignition temp: NDA

Fire Extinguishing Media: Any available extinguishing including water spray, carbon dioxide, dry chemical, Halon 1211

Special Fire-Fighting Information: Spilled chemical creates extremely slippery conditions, especially in contact with water. Use caution. Respiratory and eye protection are reqyired. Petroleum component is combustible, if separated from other ingredients. Vapors/fumes will ignite.

Unusual Fire and Explosion Hazards: Hydrocarbon components are combustible if separated from the emulsion.

green divider line

 6. Accidental Release Measures

Remove sources of ignition. Contain and collect, using a suitable absorbent, if needed. Place into suitable container(s) for disposal. Thoruhgly flush residuals to drain, as spilled product creates extremely slippery conditions.

green divider line

 7. Handling and Storage

 Handle as an irritant. Do not get in eyes. Avoid prolonged/repeated skin contact. Do not inhale vapors/mists. Do not ingest. Store away from sources of ignition. Spilled product creates very slippery condition, especially in contact with water.

green divider line

 8. Exposure Controls/ Personal Protection

  • Ventilation System: Good general ventilation is advisable. Local exhaust desired.
  • Personal Respirators (NIOSH Approved): None required for normal use and processes. if needed, use respirator to filter out mists/vapors.
  • Skin Protection: Long sleeved clothing, impervious rubber or neoprene gloves and protective apron.
  • Eye Protection: Safety glasses or goggles
  • Other Control Measures: Minimize exposure in accordance with good hygiene practice. Avoid handling which would create large amounts of mists/vapors. Exxon Medical Research recommended inhalation TLV for CAS 64742-47-8 of 200 ppm.

green divider line

 9. Physical and Chemical Properties

  • Appearance and Color: Milky-white emulsion.
  • Odor: Mild petroleum and acrylate
  • Solubility in Water: 0.5 - 1%
  • Specific Gravity: 1.13
  • Viscosity at 28 deg. C: < 4000 cps
  • % volatile by volume @ 21C (70F): NDA
  • Boiling Point: > 210 degrees F
  • Melting Point: < 23 degrees F
  • Freezing Point: - 15 degrees C
  • Vapor Density (Air=1): > 1
  • Vapor Pressure (mm Hg): 37
  • Evaporation Rate (Bu. Acetate=1): < 1

green divider line

 10. Stability and Reactivity

  • Stability: Product is stable.
  • Hazardous Decomposition Products: None known
  • Hazardous Polymerization: will not occur.
  • Incompatibility: Strong oxidizers: liquid chlorine, concentrated oxygen, sodium hypochlorite, calcium hypochlorite
  • Conditions to Avoid: Incompatible substances

green divider line

 11. Toxicological Information

  • Toxicological Data:
RTECS: CAS 2607-38-3: MD0906000, WZ4725000; CAS 25085-02-3: 1011973HP; CAS 64642-47-8: OA5504000
Eye & skin irritant. May aggravate existing medical conditions, such as rashes, allergies or other sensitive areas. Symptoms may include reddening, swelling of effected areas with possible itching, burning or other discomfort.
  • Carcinogenicity: Not listed by ACGIH, IARC, NIOSH, NTR, or OSHA

green divider line

 12. Ecological Information

  • Environmental Fate: CAS# 25085-02-3: Aquatic LC50, Ceriodaphnia dubia, 48 hours = 1.55 ppm/ Pimephales promeias, 48 hours = 12.0 ppm
    BOD (Biological Oxygen Demand) = 383,000 mg/L
    COD (Chemical Oxygen Demand) = 1.930,000 mg/L
  • Environmental Toxicity: NDA
  • Biodegradability: Laboratory studies indicate limited biodegradation with "non-acclimated sludge", based on component data, but cultures in Alken Clear-Flo 7004 are easily able to metabolize the nonylphenol sufactant and petroleum solvent in Alken Solutions A3050L.Products of biodegradation are less hazardous than original polymer ingredients.

green divider line

 13. Disposal Considerations

 RCRA Hazard Class (if discarded): Neat, unused product is not considered a hazardous waste, according to RCRA regulations 40 CFR 261. . For proper disposal of used materials, an assessment must be completed to determine the proper waste management options permissible under applicable rules, regulations and/or laws governing client's location. Use until less than 1 inch remains in the container, triple rinse with clean water, and pour rinse water to sewer. Then remove or deface product label to avoid confusion if pail or drum is later refilled. Clean, empty containers should be recycled or disposed of through an approved waste management facility.

green divider line

14. Transportation Information

  • DOT Proper Shipping Name: Not regulated as hazardous by DOT or Canadian TDG
  • DOT Hazard Class: None
  • DOT Label: Class 60:(NMFC item #4612, LTL) "adhesives, adjuvents, spreaders, sliders, liquid, in pails or drums" Alken Solutions A3050L, anionic acrylamide polymer liquid

green divider line

 15. Regulatory Information

  • TSCA: : (40CFR 710) All chemical ingredients are listed on the TSCA 8(b) inventory. None of the ingredients are on the Health and Safety Reporting List, are under Chemical Test rule, are listed under TSCA Section 12B, or have a SNUR under TSCA
    CERCLA Reportable Quantity: This product does NOT contain ingredients that have Reportable Quantity (RQ) requirements under US 40 CFR 117.302

    Section 302/304 Extremely Hazardous Substances: None

    Section 311 Hazard Categorization: None

    Section 313 Toxic Chemicals: None 

  • Clean Water Act: None of the chemicals in this formula are listed as Priority Pollutants under CWA.
  • Clean Air Act : Ingredients not listed as hazardous pollutants under CAA. This product does not contain any Class 1 or Class 2 ozone depletors, nor was it made with such chemicals.
  • OSHA: None of the ingredients are considered Extremely Hazardous by OSHA.
  • STATE RIGHT-TO-KNOW LAWS:. Ingredients not listed on California, Connecticut, Florida, Illinois, Louisiana, Massachusetts, New Jersey, New York, Pennsylvania, or Rhode Island.
  • Not subject to California Proposition 65 labeling requirements
  • Canadian WHMIS Classification: CAS 64742-47-8: B3. Combustible Liquid, but flash point of formulated product has a flash pint above flammable-combustible limit for Canada
  • Canadian DSL: all ingredients listed and compliant
  • Canada's Ingredient Disclosure List: Light hydrotreated kerosine solvent CAS# 64742-47-8, comprising 25% of this product IS listed on the CIDL, but other ingredients are "NOT CONTROLLED". This MSDS has been prepared according to the hazard criteria of the Controlled Products Regulations (CPR) and the MSDS contains all of the information required by the CPR.
  • TDG Classification: Not regulated as hazardous by Canadian TDG.
  • IHT Codes: 3906.90.5000

green divider line

16. Other Information

Reason for Revision: Routine review & revision

Alken-Murray Corporation provides the information contained herein in good faith, in compliance with the Occupational Safety and Health Act of 1970, but makes no representation as to its comprehensiveness or accuracy. This document is intended only as a guide to the appropriate precautionary handling of the material by a properly trained person using this product. Alken-Murray warrants that this product is of merchantable quality. The implied warranty of fitness for a particular purpose is limited to the extent the products are used for the purpose or uses described on the product's label or in any written instructions or materials distributed to the buyer by Alken-Murray and is hereby disclaimed should buyer use the products in a manner inconsistent with this uses or purposes described therein. In no event shall Alken-Murray be liable for any consequential, exemplary, or incidental damages incurred by buyer even if it has been advised of the possibility of such damages.


Polymer Market || Industry vs. Applications || Standard Jar Test || Polymer Dilution || Emulsion Breaking Solution || Buchner Funnel Test || Operational Tips || AS A3025L || AS A3040L || AS A3050L || AS A4040L ||  AS C111K || AS C133K || AS C186K || AS C187K || AS C189K || AS C193K || AS N3100L ||

link to Alken-Murray homepage

 Clear-Flo || Even-Flo || Demulsifier || Polymers || Chemicals || American SH Cats